//GORILLA WOOD GLUE

GORILLA WOOD GLUE

Gorilla Wood Glue is an adhesive that woodworkers, carpenters and hobbyists trust for their woodworking projects. Gorilla Wood Glue, a PVA glue, offers the benefits of an easy-to use, water-based adhesive, with Gorilla strength. This PVA glue is incredibly water resistant and dries a natural color that offers an invisible bond line for your projects.

Category:

Description

TOUGH, DRIES NATURAL COLOR, NO FOAM WOOD GLUE

Gorilla Wood Glue is an adhesive that woodworkers, carpenters and hobbyists trust for their woodworking projects. Gorilla Wood Glue, a PVA glue, offers the benefits of an easy-to use, water-based adhesive, with Gorilla strength. This PVA glue is incredibly water resistant and dries a natural color that offers an invisible bond line for your projects.

PRODUCT FEATURES

  • Complete Projects Fast: Requires only 20-30 minutes of clamp time, fully cured in 24 hours.
  • Use Indoors or Outdoors: Passes ANSI/HPVA Type II water resistance.
  • Versatile: Ideal for use on hardwoods, softwoods, and natural wood composites.
  • Dries natural color: Offering a natural bond line.

Instructiuni de utilizare

  1. Application

    For best results, it is essential that the wood surfaces are prepared prior to application of glue. For laminating, the surfaces should be planed smooth, leaving the board surface free from machine marks, tear-out and snipes. Also, be careful to avoid burnishing and end snipes. Just how much Gorilla Wood Glue to apply depends on many factors. In general, apply a generous amount of glue on one of the surfaces. On hard-to-glue woods, apply the glue on both surfaces. Rub together with the other surface to distribute the glue evenly on both surfaces. Enough glue should be applied so that a fine bead of glue squeeze-out will occur when clamping. Coverage: 1 gallon of Gorilla Wood Glue will cover about 200 square feet. 1 fluid ounce will cover approximately 1.6 square feet.

  2. Clamping

    The technique and type of clamp to be used is determined by many factors: the specific type of joint, type of stock or lumber, moisture content of stock, room temperature, assembly time and surface quality. In general, apply enough pressure that will cause a fine bead of glue to squeeze out when the proper pressure is applied.

    Clamping Time (amount of time pressure needs to remain applied): 20–30 minutes for room temperature applications. The temperature must be above 55°F. Note that clamping time can be dependent on temperature, humidity, and the porosity of the wood.

    Cure Time (amount of time for glue to reach total bonding strength): 24 hours

  3. Clean Up

    Clean up while glue is wet: Use a clean, damp cloth to wipe off excess glue. Make as many passes as needed with the clean area of the cloth to remove all the glue. When areas have completely dried, sand as needed. Wash hands, skin and damp cloths in soap and warm water, then rinse.

    Clean up when glue has dried: Use a sharp putty knife, razor, or sharp scraper to shave hardened glue from surface, then sand as needed. Soak hands and skin in soap and warm water, wash, then rinse.

    Cleaning the bottle tip: Use a clean, damp cloth to wipe off excess glue after closing. If tip becomes clogged with dry glue, remove the cap and push the clog backwards with a toothpick, then rinse cap with warm water.

    To remove Gorilla Wood Glue from hands, wash with warm soap and water.

Specificatii tehnice

Application Temperature

55° to 75° F, best at room temperature

Service Temperature

0° to 150° F

Outdoor

Yes, under covered area

Moisture Resistant

Water resistant – not recommended for continual water exposure

Paintable

Yes

Sandable

Yes

Stainable

Yes

Cured Color

Natural tan wood color

Technical Standards

ANSI/HPVA Type II

Storage Tips

Store at room temperature. Wipe excess glue from spout and keep sealed.

Gap Filling

No

Intrebari frecvente

How do I remove Gorilla Wood Glue from my surface?

To clean up while glue is wet, use a clean, damp cloth to wipe off excess glue. Make as many passes as needed with the clean area of the cloth to remove all the glue. When areas have completely dried, sand as needed. To clean up glue that has dried, use a sharp putty knife, razor, or sharp scraper to shave hardened glue from surface, then sand as needed.

Gorilla Wood Glue is too thick for my application; can I thin this glue?

Gorilla Wood Glue, unlike Original Gorilla Glue, is a water-based adhesive. You can thin Gorilla Wood Glue by adding water (not to exceed 5% weight).

Will Gorilla Wood Glue bond plastic/vinyl/rubber?

Gorilla Wood Glue is intended for use on hardwoods, softwoods, cardboard, cork, and composite lumber.

Is Gorilla Wood Glue food safe?

Once cured, Gorilla Wood Glue complies with FDA #CFR21 175.105 for indirect food contact and can be used on projects such as salad bowls and cutting boards.

How can I clean a clogged tip?

To clean the bottle tip, use a clean, damp cloth to wipe off excess glue after closing. If tip becomes clogged with dry glue, remove the cap, pull off the nozzle, and push the clog backward with a toothpick, then rinse cap with warm water. If you have difficulty pulling up on the nozzle, use a pair of pliers or scissors placed at the base of the nozzle and twist slightly.

What should I do if I think a human or animal has ingested Gorilla Wood Glue?

For medical emergencies, call 1-800-420-7186 anytime to reach a member of our product safety team. Additional product safety and first aid information can be found at: http://www.gorillatough.com/first-aid

How do I remove Gorilla Wood Glue from body/skin?

To remove Gorilla Wood Glue from hands, wash with soap and warm water.

Intrebuintari